Home of the Squeezebox™ & Transporter® network music players.
Page 277 of 278 FirstFirst ... 177227267275276277278 LastLast
Results 2,761 to 2,770 of 2772
  1. #2761

    EDO forgets DAC

    Hi, when I had switched off the NAD C510 Preamp/DAC, the Touch was asleep and I switch on both again, I need to 1st switch to "Digital Output" (reboot) and then to "NAD C510" in the extended settings menu.
    This is a pretty annoying procedure. Is it possible to avoid this and make the Touch recognize the C510 right away or remember it?
    Thanks

  2. #2762
    Senior Member
    Join Date
    Jan 2011
    Location
    Staffordshire. UK
    Posts
    5,224
    Quote Originally Posted by mo5265654 View Post
    Hi, when I had switched off the NAD C510 Preamp/DAC, the Touch was asleep and I switch on both again, I need to 1st switch to "Digital Output" (reboot) and then to "NAD C510" in the extended settings menu.
    This is a pretty annoying procedure. Is it possible to avoid this and make the Touch recognize the C510 right away or remember it?
    Thanks

    I have just tested; using a Micromega Mydac connected to the Touch (with EDO) via a usb cable.

    Power off the Touch whilst listening to fip radio stream (use the screen back arrow in the top left corner). The touch screen is set to display the time.

    The usb connection led on the Mydac is solid (connected).

    Pull the plug on the Touch (I don't have a power strip with switches). The Mydac USB led starts to flash (showing it is disconnected)

    Pull the plug on Mydac.

    Wait for the capacitors to discharge

    Plug in the Mydac, the usb input input starts flashing.

    Plug in the Touch, wait (30 secs or so) the station continues playing.

    This is, off course, over a much shorter timescale, not overnight, so may vary.

    There is a thread (somewhere) on using udev rules to give what you seem to want; Touch in sleep mode, power on Dac (essentially hot-plug to the Touch).

    I think I have seen a reference to this in the piCoreplayer help documentation

    ronnie

  3. #2763
    Senior Member
    Join Date
    Jan 2011
    Location
    Staffordshire. UK
    Posts
    5,224
    After my last posting I powered off the Touch and dac in the sequence described.

    I have just powered on the devices (after 90 minutes) as per the posting and the only difference is that the Touch booted to the home screen without playing music.

    I tapped the quaver icon and the now playing screen said "Stopped" I tapped play and the station stared playing again

    ronnie

  4. #2764
    Thanks for your testing.

    This evening I switched on the DAC first and when it had booted (it really boots and needs some time ), I started a playlist on the Touch and it worked that way.
    Will keep an eye and look at the threads you referred to.

    Thanks

  5. #2765
    Junior Member
    Join Date
    Dec 2011
    Posts
    27

    EDO issue?

    I have EDO installed. As of yesterday, the Touch no longer shows USB option when I click on select audio output. I have uninstalled the app and reinstalled it to no avail.

  6. #2766
    Senior Member
    Join Date
    Jan 2011
    Location
    Staffordshire. UK
    Posts
    5,224
    Quote Originally Posted by Shivaji View Post
    I have EDO installed. As of yesterday, the Touch no longer shows USB option when I click on select audio output. I have uninstalled the app and reinstalled it to no avail.

    Not much information to go on here

    So a couple of suggestions:

    Reset the touch (press the small button above the power inlet at power on).

    or

    Connect the Touch to mysqueezebox.com; check if a change of software is offered. If it is, proceed with the update.

    Then reinstall EDO.

    Edit: if you then connect to your local lms, you will be offered another software update; accept this. It may be necessary to reinstall EDO

    Make sure the Dac is connected and powered on whilst trying these suggestions.

    More info about your set-up may help, including what happened when things went wrong

    ronnie
    Last edited by Man in a van; 2022-07-31 at 15:02.

  7. #2767
    Junior Member
    Join Date
    Dec 2011
    Posts
    27
    Thanks for the suggestions.

  8. #2768
    Junior Member
    Join Date
    Aug 2012
    Posts
    24
    Quote Originally Posted by syrah View Post
    I ploughed through this thread but could not find anyone who has reported using the new Modius with an SBT on EDO 1.0. Everything appears to be OK except that there is no sound. SBT recognises the DAC as Schitt Modius Unison USB and also displays the sampling rates of the different tracks being played.

    Just no music; not a mouse stirring. Feeling a bit shitty.
    Same here :-(

    I got a Modius DAC this week. I installed EDO, set the digital output to USB, the DAC is recognized and shows output info but no sound. I've confirmed the correct inputs, etc. Coax and optical outputs of the Squeezebox touch work correctly to the same DAC. I've tried various digital output USB settings but to no avail. I've never used USB digital output of my squeezebox touch, and have no other devices that I can connect for testing.

    Just wondering if a solution was found for this issue?

    Info:

    Server: Version: 8.1.1 - 1610364020 @ Thu Jan 14 06:27:19 CET 2021
    Player: Firmware: 7.8.0-r16754
    EDO: 0.10 (is there a later version?)

    edit: seems to be a common issue, so I am assuming that EDO is not compatible with the USB implementation in this DAC.
    Last edited by JohnQCitizen; 2022-08-16 at 03:08.

  9. #2769
    Junior Member
    Join Date
    Aug 2022
    Posts
    2
    Ugh. Could use some suggestions on where I have gone wrong.

    Touch connected via ethernet cable. Coax from touch to Oppo bdp-105. Works flawlessly at 96/24, but I cannot seem to achieve any sound at 192khz. Using Roon. When I select the 192 khz file, the album art shows on the Touch, but no sound.

    --

    1) Ensure your Squeezebox Touch is running 7.7.x or later firmware
    Done

    2) Go to Apps Gallery -> 3rd Party Apps on the touch screen
    Done

    3) Deselect the "recommended applets only" option, so that you see a longer list of apps
    Done

    4) Select "Enhanced Digital Output" and select it for installation
    Done

    5) Your touch should download the app, reboot, then download a new custom linux kernel and reboot again.
    Done

    6) You should now get a list of possible output devices - this should include "Digital Output" and your USB Dac if it is plugged in, select the appropriate output

    Shows Digital Only [current], but when I press on that, nothing happens. I tried switching to a digital optical cable but no change. When it boots up, it indicates that EDO is installed. Tried uninstalling and reinstalling. Is it not recognizing the DAC for some reason?

  10. #2770
    Senior Member
    Join Date
    Jan 2011
    Location
    Staffordshire. UK
    Posts
    5,224
    Quote Originally Posted by MyNaimIs View Post
    Ugh. Could use some suggestions on where I have gone wrong.

    Touch connected via ethernet cable. Coax from touch to Oppo bdp-105. Works flawlessly at 96/24, but I cannot seem to achieve any sound at 192khz. Using Roon. When I select the 192 khz file, the album art shows on the Touch, but no sound.

    --

    1) Ensure your Squeezebox Touch is running 7.7.x or later firmware
    Done

    2) Go to Apps Gallery -> 3rd Party Apps on the touch screen
    Done

    3) Deselect the "recommended applets only" option, so that you see a longer list of apps
    Done

    4) Select "Enhanced Digital Output" and select it for installation
    Done

    5) Your touch should download the app, reboot, then download a new custom linux kernel and reboot again.
    Done

    6) You should now get a list of possible output devices - this should include "Digital Output" and your USB Dac if it is plugged in, select the appropriate output

    Shows Digital Only [current], but when I press on that, nothing happens. I tried switching to a digital optical cable but no change. When it boots up, it indicates that EDO is installed. Tried uninstalling and reinstalling. Is it not recognizing the DAC for some reason?
    Edit: I'm suggestioning that you should connect the touch and dac with a usb2 cable and reboot the Touch (with the dac powered on).

    You should then see the dac in the output list, select it and the Touch will reboot and install the kernel for the dac.

    Then choose the option for digital only (if that is what you want)

    I think a handshake is needed between the dac and touch for 192kHz.

    Ignore most of the stuff below

    ronnie

    If you see only "Digital Output" at #6, the dac has not been identified.

    You should see the option to select the dac as output, when you do, the Touch should reboot.

    Things to check:

    Is the dac powered on

    On the touch; go to Settings > Advanced > scroll down to software update > you may have a choice of software

    Reset the Touch and go through the procedure again; If you connect to mysqueezebox.com, check and select the offered software change

    Then install EDO (it should be available at step #2), Aafter installation, again check for a software update (is should offer lms or mysqueeze)

    It's all a bit tedious I know

    There is no guarantee that it will work

    There was link to a spreadsheet with details of working dacs but that seems to have been deleted ?

    ronnie
    Last edited by Man in a van; 2022-08-24 at 00:51. Reason: add info

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •