Home of the Squeezebox™ & Transporter® network music players.
Page 2 of 2 FirstFirst 12
Results 11 to 15 of 15
  1. #11
    Member
    Join Date
    Dec 2009
    Location
    Brooklyn, New York, USA
    Posts
    50
    Thanks Joe for the part info, and to the rest of you who provided helpful comments.

    In my case, the leaf inside the socket that's supposed to contact the outer sleeve and hold it in place seems to have broken. Thus there is no stable contact and there is no friction to hold the plug in place. Indeed Logitech seems to have used a substandard part that just didn't hold up. I have never seen a barrel connector disintegrate like this with just normal use before or since.

  2. #12
    Senior Member JoeMuc2009's Avatar
    Join Date
    Jan 2009
    Location
    Muenster, Germany
    Posts
    161
    Well, the spare parts I have here are no different from the ones used by Logitech or Slimdevices. I would not presume they chose a particularly bad part to save a penny or two. There is no supplier that I know of who would offer these parts in a higher quality level. Power connectors are rarely available in high-end quality, and the 5.5mm diameter does not allow for much ruggedness. The main issue is corrosion. The plating becoming loose is either a result of too harsh cleaning procedures or wrong chemicals used for cleaning, or the connector being plugged and unplugged too many times which will also wear out the spring contact and cause it to rupture.
    If the connector is plugged in with violence or the plugged-in connector is bent a lot, the plastic surrounding the jack may give way at some point which will also cause bad contact of course. Once that happened, it is definitely time to replace the part.

    I have five Booms currently and some had corrosion, but over time (some years) there was no deterioration of the contacts. If the Boom just sits there, the contacts will stay intact at least mechanically. They may require cleaning from time to time but if done with appropriate care, it should not cause problems. By the way, corrosion can be prevented or at least be postponed a lot with just a bit of contact spray.


    PN me if your Boom / Classic / Transporter display has issues!

    Blog: https://www.blogger.com/blogger.g?ri...50753#allposts

  3. #13
    Junior Member
    Join Date
    Aug 2018
    Posts
    1

    loose power connector cuts out with slightest movement

    I have a similar problem to what is described in this thread
    Loved my Boom and it's demise is annoying
    Pleased to have found this forum although I have almost no technical ability
    Can't even figure out how to open her up ?

  4. #14
    Senior Member JoeMuc2009's Avatar
    Join Date
    Jan 2009
    Location
    Muenster, Germany
    Posts
    161
    Quote Originally Posted by PaulShorty View Post
    I have a similar problem to what is described in this thread
    Loved my Boom and it's demise is annoying
    Pleased to have found this forum although I have almost no technical ability
    Can't even figure out how to open her up ?
    Opening a Boom is described here (ignore the part about the display): https://joes-tech-blog.blogspot.com/2016/06/logitech-squeezebox-boom-vfd-display.html

    You will have to get the mainboard out completely to get to the connector (it is located on the daughterboard that stands off the mainboard in a 90 degree angle). But some experience with soldering is definitely required, and you will need the right spare part.


    PN me if your Boom / Classic / Transporter display has issues!

    Blog: https://www.blogger.com/blogger.g?ri...50753#allposts

  5. #15
    Junior Member
    Join Date
    Nov 2005
    Posts
    2
    Conductive metal sticky tape. About twice as wise as a fingernail clipping. Stack a few if necessary on one side of the plug, leaving 4/5ths of the plug bare. It should snug it up nicely. Works.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •