USB Remote Control

[Frapicore]

Dear Comunity, please could you advise how to setup an USB remote control in piCore player? I have bought the remote below:
https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1

Is there any chance to make it work?

Thanks!!!

[Paul Webster]

See https://forums.slimdevices.com/showt...e-control-keys
There might be other relevant threads - but look for ones related to USB remotes not GPIO-based.

[Frapicore]

See https://forums.slimdevices.com/showt...e-control-keys
There might be other relevant threads - but look for ones related to USB remotes not GPIO-based.

Thank you for your quick answer. I have read the thread you kindly shared. I have put the dongle on my rpi 4 with pCp but the remote is not working. I have tried the remote with my TV and it is working on the TV.

How can I enable the remote control, as it does not seem working at the moment with pcp? Reading the forum, I have tried to install Jivelite and IR remote control (just install without set them up), but nothing happened. Any advice? Thanks

[Paul Webster]

Did you see anything when you checked the dmesg outout?

[Frapicore]

Where can I check the dmesg output? I am so sorry for my basic skills

[Frapicore]

Where can I check the dmesg output? I am so sorry for my basic skills

I have found dmesg outout but I cannot what to check. I am using a USB Dac as well.

Hoping this can be useful:

[ 8589.862823] usb 1-1.3: USB disconnect, device number 4
[ 9119.901503] usb 1-1.3: new full-speed USB device number 6 using xhci_hcd
[ 9120.036939] usb 1-1.3: New USB device found, idVendor=1915, idProduct=1047, bcdDevice= 1.78
[ 9120.036958] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 9120.036975] usb 1-1.3: Product: ZY Control
[ 9120.036990] usb 1-1.3: Manufacturer: ZY.Ltd
[ 9120.047610] input: ZY.Ltd ZY Control as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.3/1-1.3:1.0/0003:1915:1047.0005/input/input7
[ 9120.112297] hid-generic 0003:1915:1047.0005: input,hidraw1: USB HID v1.01 Keyboard [ZY.Ltd ZY Control] on usb-0000:01:00.0-1.3/input0
[ 9120.121133] input: ZY.Ltd ZY Control Mouse as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.3/1-1.3:1.1/0003:1915:1047.0006/input/input8
[ 9120.121734] input: ZY.Ltd ZY Control Consumer Control as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.3/1-1.3:1.1/0003:1915:1047.0006/input/input9
[ 9120.191920] input: ZY.Ltd ZY Control System Control as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.3/1-1.3:1.1/0003:1915:1047.0006/input/input10
[ 9120.192506] hid-generic 0003:1915:1047.0006: input,hiddev96,hidraw2: USB HID v1.01 Mouse [ZY.Ltd ZY Control] on usb-0000:01:00.0-1.3/input1

[Paul Webster]

See the example in the thread that I linked to.

Did you reboot with the USB part already attached?

Your should not need lirc for this because your remote almost certainly emulates a keyboard.

[Frapicore]

See the example in the thread that I linked to.

Did you reboot with the USB part already attached?

Your should not need lirc for this because your remote almost certainly emulates a keyboard.

Can it be useful:

Hoping this can be useful:

[ 8589.862823] usb 1-1.3: USB disconnect, device number 4
[ 9119.901503] usb 1-1.3: new full-speed USB device number 6 using xhci_hcd
[ 9120.036939] usb 1-1.3: New USB device found, idVendor=1915, idProduct=1047, bcdDevice= 1.78
[ 9120.036958] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 9120.036975] usb 1-1.3: Product: ZY Control
[ 9120.036990] usb 1-1.3: Manufacturer: ZY.Ltd
[ 9120.047610] input: ZY.Ltd ZY Control as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.3/1-1.3:1.0/0003:1915:1047.0005/input/input7
[ 9120.112297] hid-generic 0003:1915:1047.0005: input,hidraw1: USB HID v1.01 Keyboard [ZY.Ltd ZY Control] on usb-0000:01:00.0-1.3/input0
[ 9120.121133] input: ZY.Ltd ZY Control Mouse as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.3/1-1.3:1.1/0003:1915:1047.0006/input/input8
[ 9120.121734] input: ZY.Ltd ZY Control Consumer Control as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.3/1-1.3:1.1/0003:1915:1047.0006/input/input9
[ 9120.191920] input: ZY.Ltd ZY Control System Control as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.3/1-1.3:1.1/0003:1915:1047.0006/input/input10
[ 9120.192506] hid-generic 0003:1915:1047.0006: input,hiddev96,hidraw2: USB HID v1.01 Mouse [ZY.Ltd ZY Control] on usb-0000:01:00.0-1.3/input1

[Paul Webster]

That looks very similar to the example linked to ... for example:

[ 9120.112297] hid-generic 0003:1915:1047.0005: input,hidraw1: USB HID v1.01 Keyboard [ZY.Ltd ZY Control] on usb-0000:01:00.0-1.3/input0

I suggest removing LIRC and restarting pCP and then try again to see if any of the remote keys have any effect at all on Jivelite.

[Frapicore]

That looks very similar to the example linked to ... for example:

[ 9120.112297] hid-generic 0003:1915:1047.0005: input,hidraw1: USB HID v1.01 Keyboard [ZY.Ltd ZY Control] on usb-0000:01:00.0-1.3/input0

I suggest removing LIRC and restarting pCP and then try again to see if any of the remote keys have any effect at all on Jivelite.

I forgot to mention, as you advised I have uninstalled IR Remote control and I left just Jivelate. After the reboot nothing changed. I have tried to put a keyboard as well. Also the keyboard is not working.

Is it possible I have to active something, maybe in LMS? just an idea.......unfortunately I have not found a lot info for this tutorial.

Any suggest?

Thanks again!!!