ANNOUNCE: Squeezelite-ESP32 (dedicated thread)

[mboxler]

Upgraded from fw: v0.5.604-IDFv3.1.5-I2S-4MFlash to v0.5.641 on my ESP-WROOM S/PDIF system via OTA, but there is no sound.
Checked with my scope and there is no S/PDIF signal coming out. Went back to 604 and am back to normal.

Did I miss a config change or something?
Thx

I thought the ESP-WROOM chip couldn't be used?

[ElFishi]

my bad, its a WROVER.

[ElFishi]

I might have screwed something then (I did a fair bit of changes in that part). I'll try tomorrow. What do the log say wrt SPDIF when booting?

something like this?

[00:03:35.215439] output_init_embedded:70 init device: SPDIF
[00:03:35.226814] output_init_common:427 supported rates: 48000 44100 
[00:03:35.227781] output_init_embedded:86 init I2S/SPDIF
I (5617) I2S: DMA Malloc info, datalen=blocksize=2048, dma_buf_count=24
I (5627) I2S: APLL: Req RATE: 88200, real rate: 88199.977, BITS: 32, CLKM: 1, BCK_M: 8, MCLK: 45158388.000, SCLK: 5644798.500000, diva: 1, divb: 0
[00:03:35.253162] output_init_i2s:236 SPDIF using I2S bck:33, ws:25, do:32
[00:03:35.264422] output_init_i2s:290 Initializing I2S mode S/PDIF with rate: 88200, bits per sample: 32, buffer frames: 256, number of buffers: 24 
[00:03:35.276850] set_amp_gpio:144 setting amplifier GPIO 13 (active:1)
[00:03:35.277995] output_thread_i2s:432 Output state is 0
[00:03:35.289590] output_thread_i2s:495 Restarting I2S.
[00:03:35.290717] output_thread_i2s:504 changing sampling rate 88200 to 44100
I (5687) I2S: APLL: Req RATE: 88200, real rate: 88199.977, BITS: 32, CLKM: 1, BCK_M: 8, MCLK: 45158388.000, SCLK: 5644798[00:03:35.290717] output_visu_init:75 Initialize VISUEXPORT 2048 16 bits samples
.500000, diva: 1, divb: 0
[00:03:35.316063] equalizer_open:51 equalizer initialized 0
[00:03:35.335243] output_init_embedded:94 init completed.
[00:03:35.336604] decode_init:153 init decode

[philippe_44]

something like this?

[00:03:35.215439] output_init_embedded:70 init device: SPDIF
[00:03:35.226814] output_init_common:427 supported rates: 48000 44100 
[00:03:35.227781] output_init_embedded:86 init I2S/SPDIF
I (5617) I2S: DMA Malloc info, datalen=blocksize=2048, dma_buf_count=24
I (5627) I2S: APLL: Req RATE: 88200, real rate: 88199.977, BITS: 32, CLKM: 1, BCK_M: 8, MCLK: 45158388.000, SCLK: 5644798.500000, diva: 1, divb: 0
[00:03:35.253162] output_init_i2s:236 SPDIF using I2S bck:33, ws:25, do:32
[00:03:35.264422] output_init_i2s:290 Initializing I2S mode S/PDIF with rate: 88200, bits per sample: 32, buffer frames: 256, number of buffers: 24 
[00:03:35.276850] set_amp_gpio:144 setting amplifier GPIO 13 (active:1)
[00:03:35.277995] output_thread_i2s:432 Output state is 0
[00:03:35.289590] output_thread_i2s:495 Restarting I2S.
[00:03:35.290717] output_thread_i2s:504 changing sampling rate 88200 to 44100
I (5687) I2S: APLL: Req RATE: 88200, real rate: 88199.977, BITS: 32, CLKM: 1, BCK_M: 8, MCLK: 45158388.000, SCLK: 5644798[00:03:35.290717] output_visu_init:75 Initialize VISUEXPORT 2048 16 bits samples
.500000, diva: 1, divb: 0
[00:03:35.316063] equalizer_open:51 equalizer initialized 0
[00:03:35.335243] output_init_embedded:94 init completed.
[00:03:35.336604] decode_init:153 init decode

Yes - It all seems good. I've also tried on a SqueezeAMP release and an I2S release configured with SPDIF parameters and they both for me. Are you sure there is not something else? Does the led emit something? Could it be somewhere else (the amp gpio for example?)

[mboxler]

my bad, its a WROVER.

Rats! Thought there was a change that I missed.

I tried to OTA 5.642, but got the dreaded HTTP error, so had to flash wired. I too got no spdif out as well. Pretty sure I filled in spdif_config and still nothing.
I left set_GPIO blank, as I'm only using pin 32 (do).

I was able to OTA back to 5.541, and got the signal back.

Mike

[philippe_44]

Rats! Thought there was a change that I missed.

I tried to OTA 5.642, but got the dreaded HTTP error, so had to flash wired. I too got no spdif out as well. Pretty sure I filled in spdif_config and still nothing.
I left set_GPIO blank, as I'm only using pin 32 (do).

I was able to OTA back to 5.541, and got the signal back.

Mike

You have to fill all ws & bck b/c I'm using an I2S to fake a SPDIF, so all lines are needed (and previously they were set for you)

[mboxler]

You have to fill all ws & bck b/c I'm using an I2S to fake a SPDIF, so all lines are needed (and previously they were set for you)

Just to be clear, I filled spdif_config with bck=33,ws=25,do=32. I am only using 1 wire from the ESP32-WROVER (32). Ground and 5v (for my led) are from PS.

I'll try again.

[philippe_44]

Just to be clear, I filled spdif_config with bck=33,ws=25,do=32. I am only using 1 wire from the ESP32-WROVER (32). Ground and 5v (for my led) are from PS.

I'll try again.

I think I got it ... a typo in the config file which was not on my local build. Try 643 as soon as it has built

[mboxler]

I think I got it ... a typo in the config file which was not on my local build. Try 643 as soon as it has built

That was fast!

Good news, was able to load 643 ota without the dreaded Error: HTTP Start read failed. (A?X�?) message.

Bad news...it's still quiet.

Mike

[philippe_44]

That was fast!

Good news, was able to load 643 ota without the dreaded Error: HTTP Start read failed. (A?X�?) message.

Bad news...it's still quiet.

Mike

Well ... then I don't know. I just tried the version from the build site, i2s only and it worked ...