Home of the Squeezebox™ & Transporter® network music players.
Page 3 of 18 FirstFirst 1234513 ... LastLast
Results 21 to 30 of 174
  1. #21
    Senior Member
    Join Date
    Feb 2008
    Posts
    320
    Quote Originally Posted by philippe_44 View Post
    Yes - It all seems good. I've also tried on a SqueezeAMP release and an I2S release configured with SPDIF parameters and they both for me. Are you sure there is not something else? Does the led emit something? Could it be somewhere else (the amp gpio for example?)
    643 and no sound via S/PDIF.
    604 works.
    I played with the LED config but there everything is as expected, green blinks as it should, red stays off, if I configure the physical red to amp it lights up when the player is switched on etc.

    I am happy to try earlier releases (when I am back from work) to find the breaking change. If you have a hunch where to start I might save some work.

  2. #22
    Senior Member
    Join Date
    May 2008
    Location
    Canada
    Posts
    6,049
    Quote Originally Posted by ElFishi View Post
    643 and no sound via S/PDIF.
    604 works.
    I played with the LED config but there everything is as expected, green blinks as it should, red stays off, if I configure the physical red to amp it lights up when the player is switched on etc.

    I am happy to try earlier releases (when I am back from work) to find the breaking change. If you have a hunch where to start I might save some work.
    So I assume that there is no light from the spdif led
    LMS 7.9 on Pi 3B+ & Odroid-C2 - SqueezeAMP!, 5xRadio, 3xBoom, 4xDuet, 1xTouch, 1 SB3. Sonos PLAY:3, PLAY:5, Marantz NR1603, Foobar2000, ShairPortW, JRiver 21, 2xChromecast Audio, Chromecast v1 and v2, Squeezelite on Pi, Yamaha WX-010, AppleTV 4, Airport Express, GGMM E5, Riva 1 & 3

  3. #23
    Senior Member
    Join Date
    Dec 2009
    Location
    Quebec City, Canada
    Posts
    320
    Quote Originally Posted by ElFishi View Post
    643 and no sound via S/PDIF.
    604 works.
    I played with the LED config but there everything is as expected, green blinks as it should, red stays off, if I configure the physical red to amp it lights up when the player is switched on etc.

    I am happy to try earlier releases (when I am back from work) to find the breaking change. If you have a hunch where to start I might save some work.
    Could you share the full configuration details here? One way to do so is to open the developers tools in your browser, go to the network tab and finally navigate to the player. There will be a JSON file transmitted at some point with all the NVS entries.
    LMS 7.9 - 1xRadio, 1xBoom, 5xDuet,3xTouch, 1 SB2. Sony PlayStation, Emby, Chromecast v1 and v2 and...
    6xSqueezeAmp!
    Contributing to Folding@Home : https://stats.foldingathome.org/donor/squeezelite-esp32

  4. #24
    Senior Member
    Join Date
    Feb 2008
    Posts
    320
    Quote Originally Posted by sle118 View Post
    Could you share the full configuration details here? One way to do so is to open the developers tools in your browser, go to the network tab and finally navigate to the player. There will be a JSON file transmitted at some point with all the NVS entries.
    Anything in addition to this?

  5. #25
    If I knew how to do what you guys are talking about I'd be glad to help.

    Not sure what ElFishi's hardware configuration is, but I'm using the Lolin d32 pro v2.0.0.

    The only NVS entry I made was spdif_config bck=33,ws=25,do=32.

    Thanks for the hard work guys! You are very much appreciated.

    Mike

  6. #26
    Senior Member
    Join Date
    Feb 2008
    Posts
    320
    Quote Originally Posted by philippe_44 View Post
    So I assume that there is no light from the spdif led
    What is the s/pdif LED? I don't use Toslink.
    Attached pls find the schematic of my player for further reference.
    The ESP is connected to the coax/RCA input of my DacMagic via a voltage divider and two caps.

    With a working fw, the dac is able to sync and indicates the incoming sample rate, and plays music.
    With a later fw there is no music, no sync, and when I check by scope, also no signal.
    Attached Images Attached Images

  7. #27
    Senior Member
    Join Date
    Feb 2008
    Posts
    320
    Quote Originally Posted by ElFishi View Post
    643 and no sound via S/PDIF.
    604 works.
    I played with the LED config but there everything is as expected, green blinks as it should, red stays off, if I configure the physical red to amp it lights up when the player is switched on etc.

    I am happy to try earlier releases (when I am back from work) to find the breaking change. If you have a hunch where to start I might save some work.
    631: music
    634: no music

  8. #28
    Senior Member
    Join Date
    May 2008
    Location
    Canada
    Posts
    6,049
    Quote Originally Posted by mboxler View Post
    If I knew how to do what you guys are talking about I'd be glad to help.

    Not sure what ElFishi's hardware configuration is, but I'm using the Lolin d32 pro v2.0.0.

    The only NVS entry I made was spdif_config bck=33,ws=25,do=32.

    Thanks for the hard work guys! You are very much appreciated.

    Mike
    Quote Originally Posted by ElFishi View Post
    631: music
    634: no music
    oh ... do you have dac_config set as well?
    LMS 7.9 on Pi 3B+ & Odroid-C2 - SqueezeAMP!, 5xRadio, 3xBoom, 4xDuet, 1xTouch, 1 SB3. Sonos PLAY:3, PLAY:5, Marantz NR1603, Foobar2000, ShairPortW, JRiver 21, 2xChromecast Audio, Chromecast v1 and v2, Squeezelite on Pi, Yamaha WX-010, AppleTV 4, Airport Express, GGMM E5, Riva 1 & 3

  9. #29
    Quote Originally Posted by philippe_44 View Post
    oh ... do you have dac_config set as well?
    I don't.

    Mike

  10. #30
    Senior Member
    Join Date
    Feb 2008
    Posts
    320
    Quote Originally Posted by philippe_44 View Post
    oh ... do you have dac_config set as well?
    dac_config is empty. Do I need to set it?
    Rest of config here.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •