Home of the Squeezebox™ & Transporter® network music players.
Page 94 of 106 FirstFirst ... 44849293949596104 ... LastLast
Results 931 to 940 of 1059
  1. #931
    Quote Originally Posted by wizmo View Post
    If you are not getting the 0x1a device (which is in fact the ac101 dac, even though the i2cdevices.org thinks its a temperature chip), I would suspect a faulty board.
    I would suggest checking functionality with one of the simpler arduino sketches out there?
    OK, I tried two different I2C-scanner sketches for arduino ide (eg sketch from section 2, SDA1=33, SLC1=32). Result is:

    Code:
    rst:0x1 (POWERON_RESET),boot:0x1f (SPI_FAST_FLASH_BOOT)
    configsip: 0, SPIWP:0xee
    clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
    mode:DIO, clock div:1
    load:0x3fff0018,len:4
    load:0x3fff001c,len:1216
    ho 0 tail 12 room 4
    load:0x40078000,len:10944
    load:0x40080400,len:6388
    entry 0x400806b4
    Scanning I2C Addresses Channel 1
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 
    Scan Completed, 0 I2C Devices found.
    
    Scanning I2C Addresses Channel 2
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 
    Scan Completed, 0 I2C Devices found.
    The second sketch did not show any i2s device either. I double checked the sketch with an ESP32-WROOM-32D and two connected I2C sensors. The sensors showed up in the matrix.

    Conclusion: Sketch is working - my ESP32-A1S is faulty.


    Can anyone double check the linked sketch from above with his ESP32-A1S or ESP32 Audio Kit V2.2? Does the AC101 show up in the matrix?

  2. #932
    Quote Originally Posted by jofland View Post

    Can anyone double check the linked sketch from above with his ESP32-A1S or ESP32 Audio Kit V2.2? Does the AC101 show up in the matrix?
    If you give a HowTo step by step, I should do it
    - DAC32 (polyvection) + turntable : Thorens TD190-2 + CD player : Marantz CD5004 + K7 player : Toshiba +ampli : Marantz PM7001 + speaker : Magnat Quantum 1005.
    - Raspberry 2 + Ampli-dac : Alientek D8 + speaker : Magnat Quantum Edelstein
    - Daphile on Acer_Aspire_One + Ampli-dac : Advance Acoustic A60 + Speaker : Elipson Studio Pro

  3. #933
    Quote Originally Posted by sitro0 View Post
    If you give a HowTo step by step, I should do it
    OK, thank you. Be aware that by doing the next steps you afterwards have to reflash your actually software (eg squeezelite) to your audio kit board.


    Here is my step by step howto:

    Prerequisit: Installed arduino ide with installed esp32. If you need a howto, you can use the one from the link beyond. Start at chapter "Installing...", end before "Testing..."
    https://randomnerdtutorials.com/inst...-instructions/

    Connect the audio kit board to your pc.

    In arduino ide select port an board as described in the link above at chapter "Testing...":
    - chose board = "ESP Dev Module"
    - chose port depends on your operating system

    In arduino ide open a blank file, insert the sketch from the attachment of this post and save the file.

    In arduino ide open the serial monitor by clicking the upper right symbol.

    In arduino ide compile and upload the sketch to the audio kit by clicking the arrow button upper left (second button) or press ctrl-U.

    After upload the board should be reset automatically.

    In the serial monitor the result of the i2c scan should appear. If your board has been working with squeezelite before there should appear an device within the matrix. That should be the proof the AC101 is detected with this script and my board is faulty. If no device will appear the sketch is insufficient.
    Attached Files Attached Files

  4. #934
    Junior Member
    Join Date
    Apr 2019
    Posts
    9
    Result from my A1S.



    rst:0x1 (POWERON_RESET),boot:0x1f (SPI_FAST_FLASH_BOOT)
    configsip: 0, SPIWP:0xee
    clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd _drv:0x00,wp_drv:0x00
    modeIO, clock div:1
    load:0x3fff0018,len:4
    load:0x3fff001c,len:1216
    ho 0 tail 12 room 4
    load:0x40078000,len:10944
    load:0x40080400,len:6388
    entry 0x400806b4
    Scanning I2C Addresses Channel 1
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. 1A .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    Scan Completed, 1 I2C Devices found.

    Scanning I2C Addresses Channel 2
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    Scan Completed, 0 I2C Devices found.

  5. #935
    same here :
    17:42:42.713 -> [D][esp32-hal-psram.c:47] psramInit(): PSRAM enabled
    17:42:42.746 -> [W][esp32-hal-i2c.c:1419] i2cCheckLineState(): invalid state sda(17)=0, scl(16)=1
    17:42:42.779 -> [E][esp32-hal-i2c.c:1434] i2cCheckLineState(): Bus Invalid State, TwoWire() Can't init sda=0, scl=1
    17:42:42.779 -> .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    17:42:42.779 -> .. .. .. .. .. .. .. .. .. .. 1A .. .. .. .. ..
    17:42:42.779 -> .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    17:42:42.779 -> .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    17:42:42.779 -> .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    17:42:42.812 -> .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    17:42:42.812 -> .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    17:42:42.812 -> .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    17:42:42.812 -> Scan Completed, 1 I2C Devices found.
    17:42:42.812 ->
    17:42:42.911 -> Scanning I2C Addresses Channel 2
    17:42:42.911 -> .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    17:42:42.911 -> .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    17:42:42.911 -> .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    17:42:42.911 -> .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    17:42:42.911 -> .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    17:42:42.911 -> .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    17:42:42.951 -> .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    17:42:42.951 -> .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    17:42:42.951 -> Scan Completed, 0 I2C Devices found.


    17:42:47.945 -> Scanning I2C Addresses Channel 1
    17:42:47.945 -> .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    17:42:47.945 -> .. .. .. .. .. .. .. .. .. .. 1A .. .. .. .. ..
    17:42:47.945 -> .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    17:42:47.945 -> .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    17:42:47.945 -> .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    17:42:47.945 -> .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    17:42:47.978 -> .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    17:42:47.978 -> .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    17:42:47.978 -> Scan Completed, 1 I2C Devices found.
    - DAC32 (polyvection) + turntable : Thorens TD190-2 + CD player : Marantz CD5004 + K7 player : Toshiba +ampli : Marantz PM7001 + speaker : Magnat Quantum 1005.
    - Raspberry 2 + Ampli-dac : Alientek D8 + speaker : Magnat Quantum Edelstein
    - Daphile on Acer_Aspire_One + Ampli-dac : Advance Acoustic A60 + Speaker : Elipson Studio Pro

  6. #936
    Thank you very much. Then my board is definitely faulty.

    The only question left is: how to convince the Chinese seller at aliexpress for a refund :-)?

  7. #937
    Junior Member
    Join Date
    Feb 2021
    Location
    near Berlin
    Posts
    14

    list of displays in readme.md (github)

    Just a short note - in the github project description (readme.md) display types SSD1322 and SSD1327 are mixed up:
    • SSD1322 is not 128x128 16-level grayscale SPI, (that would be SSD1327)
    • SSD1327 is not 256x64 grayscale 16-levels SPI in multiple sizes (that is SSD1322)

    Indeed, the SSD1322 is a very nice display, although the 5.5 inch variant is a little bit expensive.

    Update: Thank you very much, philippe44, for correcting readme.md!
    Last edited by df77; 2021-06-24 at 23:01. Reason: thanks for updating readme.md

  8. #938
    Senior Member
    Join Date
    May 2008
    Location
    Canada
    Posts
    7,326

    ANNOUNCE: Squeezelite-ESP32 (dedicated thread)

    Quote Originally Posted by df77 View Post
    Just a short note - in the github project description (readme.md) display types SSD1322 and SSD1327 are mixed up:
    • SSD1322 is not 128x128 16-level grayscale SPI, (that would be SSD1327)
    • SSD1327 is not 256x64 grayscale 16-levels SPI in multiple sizes (that is SSD1322)

    Indeed, the SSD1322 is a very nice display, although the 5.5 inch variant is a little bit expensive.

    Update: Thank you very much, philippe44, for correcting readme.md!
    Thanks for pointing out the mistake
    LMS 8.2 on Odroid-C4 - SqueezeAMP!, 5xRadio, 5xBoom, 2xDuet, 1xTouch, 1xSB3. Sonos PLAY:3, PLAY:5, Marantz NR1603, Foobar2000, ShairPortW, 2xChromecast Audio, Chromecast v1 and v2, Squeezelite on Pi, Yamaha WX-010, AppleTV 4, Airport Express, GGMM E5, RivaArena 1 & 3

  9. #939
    Junior Member
    Join Date
    Jun 2021
    Posts
    7
    I have the same problem. Did you find any solution?

    Scanning I2C Addresses Channel 1
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    Scan Completed, 0 I2C Devices found.

    Scanning I2C Addresses Channel 2
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    Scan Completed, 0 I2C Devices found.

    Scanning I2C Addresses Channel 1
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    Scan Completed, 0 I2C Devices found.

    Scanning I2C Addresses Channel 2
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    Scan Completed, 0 I2C Devices found.

    Scanning I2C Addresses Channel 1
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    Scan Completed, 0 I2C Devices found.

    Scanning I2C Addresses Channel 2
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    Scan Completed, 0 I2C Devices found.

    Scanning I2C Addresses Channel 1
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    Scan Completed, 0 I2C Devices found.

    Scanning I2C Addresses Channel 2
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    Scan Completed, 0 I2C Devices found.

    Scanning I2C Addresses Channel 1
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
    Scan Completed, 0 I2C Devices found.



    Quote Originally Posted by jofland View Post
    OK, thank you. Be aware that by doing the next steps you afterwards have to reflash your actually software (eg squeezelite) to your audio kit board.


    Here is my step by step howto:

    Prerequisit: Installed arduino ide with installed esp32. If you need a howto, you can use the one from the link beyond. Start at chapter "Installing...", end before "Testing..."

    Connect the audio kit board to your pc.

    In arduino ide select port an board as described in the link above at chapter "Testing...":
    - chose board = "ESP Dev Module"
    - chose port depends on your operating system

    In arduino ide open a blank file, insert the sketch from the attachment of this post and save the file.

    In arduino ide open the serial monitor by clicking the upper right symbol.

    In arduino ide compile and upload the sketch to the audio kit by clicking the arrow button upper left (second button) or press ctrl-U.

    After upload the board should be reset automatically.

    In the serial monitor the result of the i2c scan should appear. If your board has been working with squeezelite before there should appear an device within the matrix. That should be the proof the AC101 is detected with this script and my board is faulty. If no device will appear the sketch is insufficient.

  10. #940
    Junior Member
    Join Date
    May 2021
    Posts
    11

    Connection Problem with 3 Squeezelite-ESP32 devices

    Hello Community,

    i just have set up a LMS on my iobroker Raspberry PI 4 which is running on Port 9002 (not standard 9000, maybe that's a part of the problem). On top of that i have 3 Wireless speakers (L; R and Sub) connected which are running based on WROVER with PCM5102A as DAC. This system is running well for several days. However i had a router problem yesterday which did lead to a reboot of the router. Since that the ESP32 are not reconnecting to the LMS. I just rebooted all of them and everything was fine after doing so. In order to verify my assumption, i just rebooted the router again and the same problems appears once again. The ESP's are connected to the network but they seem not to be discovered by the LMS. Please find the Telnet Log of one of those ESP's:

    Code:
    I (7018598) wifi_manager: Wifi Connecting...
    W (7020648) wifi_manager: Wifi disconnected. Number of disconnects: 58, Average                                                                                                              time connected: 118
    E (7020648) wifi_manager: WiFi Connection lost.
    I (7020648) wifi_manager: Wifi Connecting...
    W (7022698) wifi_manager: Wifi disconnected. Number of disconnects: 59, Average                                                                                                              time connected: 116
    E (7022698) wifi_manager: WiFi Connection lost.
    I (7022698) wifi_manager: Wifi Connecting...
    I (7024748) wifi:new:<11,0>, old:<1,0>, ap:<255,255>, sta:<11,0>, prof:1
    I (7024748) wifi:state: init -> auth (b0)
    I (7024758) wifi:state: auth -> assoc (0)
    I (7024758) wifi:state: assoc -> run (10)
    I (7024788) wifi:connected with StaSi Zentralnetz, aid = 1, channel 11, BW20, bs                                                                                                             sid = 38:10:d5:7f:c2:28
    I (7024788) wifi:security: WPA2-PSK, phy: bgn, rssi: -58
    I (7024788) wifi:pm start, type: 1
    
    I (7024798) wifi:AP's beacon interval = 102400 us, DTIM period = 1
    I (7024828) tcpip_adapter: sta ip: 192.168.178.72, mask: 255.255.255.0, gw: 192.                                                                                                             168.178.1
    I (7024828) wifi_manager: SYSTEM_EVENT_STA_GOT_IP. IP=192.168.178.72, Gateway=19                                                                                                             2.168.178.1, NetMask=255.255.255.0, Address was changed
    I (7024838) esp_app_main: Wifi connected!
    Anyone already faced this topic. What additional information do you need to better understand this.

    Thanks in advance
    christi_ko

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •