Home of the Squeezebox™ & Transporter® network music players.
Page 1 of 5 123 ... LastLast
Results 1 to 10 of 45
  1. #1

    Unable to reach LMS web gui after fresh installation

    I installed LMS 7.9.1 on a fresh install of Raspbian Buster. The service is up and running, which I check with service logitechmediaserver status. There are no disks connected to the Raspi and no media should be scanned. However, I can not access the web gui under http://RaspiIP:9000. I can ping the Raspi of course from my Laptop and I am logged into via SSH.

    I downloaded the ARM64.deb from here and my Pi is 3 Model B http://downloads.slimdevices.com/Log...Server_v7.9.1/.

    I have a second Raspi running in my network, but of course under a different IP since it is another ethernet port. It is reachable via browser. I also use 7.9.1 there.

    I read a lot about this problem online and came across the cache problem which does not apply here. I also checked with another browser I never use.

    Where can I check if the port 9000 is correct? Is there another reason for the problem?

  2. #2
    Senior Member
    Join Date
    Jan 2011
    Location
    Staffordshire. UK
    Posts
    2,918
    This is the LMS for a raspberry pi

    http://downloads.slimdevices.com/nig...788734_arm.deb

    On the Buster Desktop open Chromium browser and enter

    Code:
    http://localhost:9000
    from another computer open

    IPAddressof pi:9000 (example 192.168.1.24:9000)

    ronnie

  3. #3
    Thanks Ronnie, I downloaded the wrong package. Interestingly I was able to install and run the AMD64.deb...

    But however, also with the correct ARM.deb my browser is not able to open the web gui.

    As I am logged into the Raspberry via SSH and have no monitor attached I cannot check if localhost would work but I suspect it wont neither.

    EDIT: I also just recognised that you put in a link to a nightly version. But I can not find the directory for nightly versions here: http://downloads.slimdevices.com/

    So I installed 7.9.1 and you suggested 7.9.2 (nightly). I guess it should also work with 7.9.1
    Last edited by bvrulez; 2019-08-08 at 07:32.

  4. #4
    Senior Member
    Join Date
    Oct 2005
    Location
    Ireland
    Posts
    17,911
    Not sure if these will work on Raspbian bur should do

    try "netstat -t -l"

    It will show which ports are being "listened" - if LMS is running you should see port 9000, 9090 and 3483

    If 9001, 9002 ... is open then something is blocking 9000 for LMS.

    The command "lsof -i" will show the processes with open internet ports. You can identify processes with ports.

  5. #5
    Thanks a lot, this is very interesting.

    I took the time in between to install the nightly 7.9.2 over my 7.9.1 and now the GUI is reachable.

    EDIT: Out of curiosity I downgraded to 7.9.1 again and used netstat to check the ports with the following result (service is active!):

    root@raspberrypi:~# netstat -t -l
    Active Internet connections (only servers)
    Proto Recv-Q Send-Q Local Address Foreign Address State
    tcp 0 0 0.0.0.0:ssh 0.0.0.0:* LISTEN
    tcp6 0 0 [::]:ssh [::]:* LISTEN

    EDIT: With 7.9.2 the ports are open. So I suspect there is something wrong with 7.9.1 !

    Proto Recv-Q Send-Q Local Address Foreign Address State
    tcp 0 0 0.0.0.0:3483 0.0.0.0:* LISTEN
    tcp 0 0 0.0.0.0:9090 0.0.0.0:* LISTEN
    tcp 0 0 0.0.0.0:9000 0.0.0.0:* LISTEN
    tcp 0 0 0.0.0.0:ssh 0.0.0.0:* LISTEN
    tcp6 0 0 [::]:ssh [::]:* LISTEN
    Last edited by bvrulez; 2019-08-08 at 07:50.

  6. #6
    Senior Member
    Join Date
    Jan 2011
    Location
    Staffordshire. UK
    Posts
    2,918
    @bvrulez

    It's best not to do too much stuff as root with the raspbery pi.

    Sudo works fine and you can use sudo su for the odd time you may need root.

    Just advice, as over on the raspberry forums they discourage using root all the time.

    ronnie
    Last edited by Man in a van; 2019-08-08 at 08:59.

  7. #7
    Senior Member
    Join Date
    Oct 2005
    Location
    Ireland
    Posts
    17,911
    Quote Originally Posted by bvrulez View Post
    EDIT: With 7.9.2 the ports are open. So I suspect there is something wrong with 7.9.1 !
    Check server.log for the reason LMS has stopped.

  8. #8
    Quote Originally Posted by Man in a van View Post
    @bvrulez

    It's best not to do too much stuff as root with the raspbery pi.

    Sudo works fine and you can use sudo su for the odd time you may need root.

    Just advice, as over on the raspberry forums they discourage using root all the time.

    ronnie
    I was not aware that there is a difference between root and sudo.

  9. #9
    Senior Member
    Join Date
    Jan 2011
    Location
    Staffordshire. UK
    Posts
    2,918
    Quote Originally Posted by bvrulez View Post
    I was not aware that there is a difference between root and sudo.


    https://www.raspberrypi.org/document.../usage/root.md

  10. #10
    Now I understand. I did not log in as "root". I used "sudo -i" to change to root. I think it is pretty much the same as "sudo su". But thanks!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •