Home of the Squeezebox™ & Transporter® network music players.
Page 2 of 2 FirstFirst 12
Results 11 to 20 of 20
  1. #11
    Junior Member
    Join Date
    Aug 2018
    Posts
    19
    So I performed the USB stick repair on a desktop linux, with fsdsk, which found some errors. But it is still not working.

    After boot, dmesg states
    Code:
    ...
    [    0.872661] mmc1: new high speed SDIO card at address 0001
    [    0.900818] Indeed it is in host mode hprt0 = 00021501
    [    0.969065] mmc0: host does not support reading read-only switch, assuming write-enable
    [    0.971945] mmc0: new high speed SD card at address abe4
    [    0.972218] mmcblk0: mmc0:abe4 SD02G 1.83 GiB
    [    0.973096]  mmcblk0: p1 p2
    [    1.110765] usb 1-1: new high-speed USB device number 2 using dwc_otg
    [    1.110884] Indeed it is in host mode hprt0 = 00001101
    [    1.351089] usb 1-1: New USB device found, idVendor=0424, idProduct=2514
    [    1.351098] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
    [    1.351652] hub 1-1:1.0: USB hub found
    [    1.351737] hub 1-1:1.0: 4 ports detected
    [    1.670728] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
    [    1.800842] usb 1-1.1: New USB device found, idVendor=0424, idProduct=2514
    [    1.800847] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
    [    1.801191] hub 1-1.1:1.0: USB hub found
    [    1.801247] hub 1-1.1:1.0: 3 ports detected
    [    3.060725] usb 1-1.1.2: new high-speed USB device number 4 using dwc_otg
    [    3.412626] zram: Added device: zram0
    [    3.425175] zram0: detected capacity change from 0 to 246484992
    [    3.427958] random: mkswap: uninitialized urandom read (16 bytes read)
    [    3.430629] Adding 240704k swap on /dev/zram0.  Priority:-2 extents:1 across:240704k SSFS
    [    3.503067] squashfs: version 4.0 (2009/01/31) Phillip Lougher
    [    3.561330] usb 1-1.1.2: New USB device found, idVendor=1f75, idProduct=0917
    [    3.561338] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
    [    3.561341] usb 1-1.1.2: Product: PenDrive
    [    3.561344] usb 1-1.1.2: Manufacturer: Innostor
    [    3.561348] usb 1-1.1.2: SerialNumber: 265254437914238
    [    3.561763] usb-storage 1-1.1.2:1.0: USB Mass Storage device detected
    [    3.562212] scsi host0: usb-storage 1-1.1.2:1.0
    [    3.660764] usb 1-1.1.3: new full-speed USB device number 5 using dwc_otg
    [    3.806938] usb 1-1.1.3: New USB device found, idVendor=0483, idProduct=5740
    [    3.806945] usb 1-1.1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
    [    3.806949] usb 1-1.1.3: Product: STM32 Audio Class
    [    3.806952] usb 1-1.1.3: Manufacturer: STMicroelectronics
    [    3.806956] usb 1-1.1.3: SerialNumber: 00000000001A
    [    4.073655] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
    [    4.110734] usb 1-1.1.1: new high-speed USB device number 6 using dwc_otg
    [    4.240936] usb 1-1.1.1: New USB device found, idVendor=0424, idProduct=7800
    [    4.240941] usb 1-1.1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
    [    4.376488] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
    [    4.507582] libphy: lan78xx-mdiobus: probed
    [    4.631139] scsi 0:0:0:0: Direct-Access     Innostor Innostor         1.00 PQ: 0 ANSI: 6
    [    4.631757] sd 0:0:0:0: [sda] 61440000 512-byte logical blocks: (31.5 GB/29.3 GiB)
    [    4.631972] sd 0:0:0:0: [sda] Write Protect is off
    [    4.631994] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
    [    4.632236] sd 0:0:0:0: [sda] Write cache: disabled, read cache: disabled, doesn't support DPO or FUA
    [    4.634489]  sda: sda1
    [    4.636085] sd 0:0:0:0: [sda] Attached SCSI removable disk
    [   10.784874] snd_bcm2835: module is from the staging directory, the quality is unknown, you have been warned.
    [   10.798572] bcm2835_alsa bcm2835_alsa: card created with 8 channels
    [   10.839049] usbcore: registered new interface driver snd-usb-audio
    [   12.153284] random: crng init done

  2. #12
    Junior Member
    Join Date
    Aug 2018
    Posts
    19
    If I then try to configure the mount of the USB stick in the LMS page, I have
    Code:
    [ INFO ] Mount options have changed for Disk .
    
    [ INFO ] Mount Point is set to: LMSfolder
    
    [ INFO ] Checking new Mount Point.
    
    [ INFO ] Mounting Disk.
    
    [ INFO ]
    
    [ERROR] Disk Mount Error, Try to Reboot.
    
    [ INFO ] Backing up files to /mnt/mmcblk0p2/tce/mydata.tgz/- Done.
    
    [ OK ] Backup successful.
    Still this disk mount error.

    And no additional message in dmesg:
    [ 10.784874] snd_bcm2835: module is from the staging directory, the quality is unknown, you have been warned.
    [ 10.798572] bcm2835_alsa bcm2835_alsa: card created with 8 channels
    [ 10.839049] usbcore: registered new interface driver snd-usb-audio
    [ 12.153284] random: crng init done
    Last edited by JMF11; 2019-05-12 at 05:57.

  3. #13
    Junior Member
    Join Date
    Aug 2018
    Posts
    19
    But I can mount manually without error:

    Code:
    sudo mount /dev/sda1 /mnt/LMSfolder
    What could be wrong now?

  4. #14
    Senior Member paul-'s Avatar
    Join Date
    Jan 2013
    Posts
    1,767
    Doesnĺt make a lot of sense, what version of pCP are you running?

    Would you mind taking a screen shot of the web interface mount section.
    piCorePlayer a small player for the Raspberry Pi in RAM.
    Homepage: https://www.picoreplayer.org

    Please donate if you like the piCorePlayer

  5. #15
    Junior Member
    Join Date
    Aug 2018
    Posts
    19
    Name:  piCore versions.JPG
Views: 39
Size:  28.1 KB

    Name:  before.JPG
Views: 40
Size:  66.3 KB

    Name:  Filled.JPG
Views: 40
Size:  43.7 KB

    Then I push the "Set USB mount point" button

    Name:  result.JPG
Views: 40
Size:  52.9 KB

  6. #16
    Senior Member paul-'s Avatar
    Join Date
    Jan 2013
    Posts
    1,767
    How was that formatted? There is no UUID. That is a problem. Reformat the drive.
    piCorePlayer a small player for the Raspberry Pi in RAM.
    Homepage: https://www.picoreplayer.org

    Please donate if you like the piCorePlayer

  7. #17
    Junior Member
    Join Date
    Aug 2018
    Posts
    19
    Will do and report here.

    Thanks for your help

  8. #18
    Senior Member paul-'s Avatar
    Join Date
    Jan 2013
    Posts
    1,767
    If you have more than one usb disk plugged in, they can be assigned different numbers each boot, so we use the uuid to know which disk to mount. Iĺve never seen a drive not have a uuid before
    piCorePlayer a small player for the Raspberry Pi in RAM.
    Homepage: https://www.picoreplayer.org

    Please donate if you like the piCorePlayer

  9. #19
    Junior Member
    Join Date
    Aug 2018
    Posts
    19
    That was the explanation Paul ! Thanks a lot.

    After reformatting (FAT32) everything went fine :-)

    Initially the USB stick was brand new, just from the blister. I understand that this uuid thing is surprising.

    It did not blocked on windows and the manual command on Linux. But you have the explanation.

    Thanks a lot !

    Best regards,

    JMF

  10. #20
    Senior Member paul-'s Avatar
    Join Date
    Jan 2013
    Posts
    1,767
    Quote Originally Posted by JMF11 View Post
    That was the explanation Paul ! Thanks a lot.

    After reformatting (FAT32) everything went fine :-)

    Initially the USB stick was brand new, just from the blister. I understand that this uuid thing is surprising.

    It did not blocked on windows and the manual command on Linux. But you have the explanation.

    Thanks a lot !

    Best regards,

    JMF
    Thanks for confirming, I'll add a trap for no UUID.
    piCorePlayer a small player for the Raspberry Pi in RAM.
    Homepage: https://www.picoreplayer.org

    Please donate if you like the piCorePlayer

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •