Home of the Squeezebox™ & Transporter® network music players.
Page 30 of 33 FirstFirst ... 202829303132 ... LastLast
Results 291 to 300 of 325
  1. #291
    Senior Member
    Join Date
    Jan 2011
    Location
    Staffordshire. UK
    Posts
    3,177
    Quote Originally Posted by slimhase View Post
    You might want to try chills setupfrom this thread. Since I added swap, my system is running stable for me.
    He prepared a img, which only needs addition of LMS and runs otherwise out of the box.
    Yeh, I have in the past tried it, but sometimes like a challenge

    ronnie

    I tend to run LMS on a rpi and use a phone app these days more than a Joggler

  2. #292
    Senior Member
    Join Date
    Jul 2009
    Posts
    488

    help needed...

    @chill;
    I hit a dead end and need some help / input to proceed:
    I want to replace roobarbs SPOS on my Joggler with your Jivelite image
    I got your image running and added LMS8 and its running nicely so far when testing it.

    However; I also want to use the Joggler as an Access Point. That worked with the old setup without problems; I followed these instructions to set it up:
    https://www.jogglerwiki.com/forum/vi...2119&start=140 (see palindroms post)

    But setting it up in a similar way does not work when using your image.

    I don't know enough about unix to pinpoint the problem.
    Could it be that WiFi is not enabled or a driver for the Jogglers WiFi card is missing in your image?

    Any feedback would be great.

    Hope everyone is well in these bad Corona times....

    The following info I could gather:

    root@openframe:~# lsusb
    Bus 001 Device 003: ID 148f:2770 Ralink Technology, Corp. RT2770 Wireless Adapter

    and:

    root@openframe:~# cat /sys/class/net/wlan0/operstate
    down

    (it stays down also after doing ifconfig wlan0 up)

    edit: Some more info:
    The above id 148f:2770 translates to 'RT3572' according to https://wiki.ubuntuusers.de/WLAN/Ralink/.
    For that I found potential driver files here: https://www.mediatek.com/products/broadbandWifi/rt3572
    But again, I don't know where to go from here....
    Last edited by slimhase; 2020-03-24 at 05:58.
    LMS 8 on Open Peak Joggler (running Chills Jivelite on Joggler)
    Player: 5 x Squeezebox Classic, Slimp3, SqueezeAmp
    2nd System: PiCorePlayer (and LMS) on Pi Zero;

  3. #293
    Senior Member
    Join Date
    Jul 2009
    Posts
    488

    Barking up the wrong tree...

    Quote Originally Posted by slimhase View Post
    @chill;
    I hit a dead end and need some help / input to proceed:
    I want to replace roobarbs SPOS on my Joggler with your Jivelite image
    I got your image running and added LMS8 and its running nicely so far when testing it.

    However; I also want to use the Joggler as an Access Point. That worked with the old setup without problems; I followed these instructions to set it up:
    https://www.jogglerwiki.com/forum/vi...2119&start=140 (see palindroms post)

    But setting it up in a similar way does not work when using your image.

    I don't know enough about unix to pinpoint the problem.
    Could it be that WiFi is not enabled or a driver for the Jogglers WiFi card is missing in your image?

    ....
    Doh!
    I overlooked that in Jilelite setup you CAN select WLAN - and it is working.
    So, my AP setup problem must be somewhere else...
    So, ignore my previous post.
    (Unless you know how to setup an AP in this envirnonment)
    LMS 8 on Open Peak Joggler (running Chills Jivelite on Joggler)
    Player: 5 x Squeezebox Classic, Slimp3, SqueezeAmp
    2nd System: PiCorePlayer (and LMS) on Pi Zero;

  4. #294
    Senior Member
    Join Date
    Jul 2009
    Posts
    488

    help needed...

    ... still banging my head against the wall with setting up an access point on this image. I moved back to the method used in SQPOS installing hostapd and bridge-utils following these instructions: Only additional thing to be done is 'systemctl unmask hostapd' and 'systemctl enable hostapd'. That makles the AP visible for my phone or Laptop! But: Login fails with 'wrong password'. When I try the log in and then do in SSH 'cat /var/log/syslog | grep hostapd',
    I get:
    Code:
    Mar 25 17:13:43 openframe hostapd: wlan0: STA 24:ee:9a:87:a9:7e IEEE 802.11: authenticated
    Mar 25 17:13:43 openframe hostapd: wlan0: STA 24:ee:9a:87:a9:7e IEEE 802.11: associated (aid 1)
    Mar 25 17:13:52 openframe hostapd: wlan0: STA 24:ee:9a:87:a9:7e IEEE 802.11: deauthenticated due to local deauth request
    When I do the same with the older SQPOS system, I get:
    Code:
    Mar 25 16:55:59 openframe hostapd: wlan0: STA e0:5f:45:a5:28:69 IEEE 802.11: authenticated
    Mar 25 16:55:59 openframe hostapd: wlan0: STA e0:5f:45:a5:28:69 IEEE 802.11: associated (aid 5)
    Mar 25 16:55:59 openframe hostapd: wlan0: STA e0:5f:45:a5:28:69 RADIUS: starting accounting session 5E7A916A-00000009
    Mar 25 16:55:59 openframe hostapd: wlan0: STA e0:5f:45:a5:28:69 WPA: pairwise key handshake completed (RSN)
    Also, when I compare the output of 'hostapd -d /etc/hostapd/hostapd.conf', the the following lines show up only in the non-working case:
    Code:
    wlan0: interface state UNINITIALIZED->DISABLED
    wlan0: AP-DISABLED
    Again - any hints, suggestions etc would be great.

    Stay save.
    LMS 8 on Open Peak Joggler (running Chills Jivelite on Joggler)
    Player: 5 x Squeezebox Classic, Slimp3, SqueezeAmp
    2nd System: PiCorePlayer (and LMS) on Pi Zero;

  5. #295
    Senior Member
    Join Date
    Jul 2009
    Posts
    488

    still help needed to setup AccessPoint...

    I am a step further understanding the problem - still can not fix it due to lack of knowlege

    The problem seems to be that Ubuntu 18.04 uses 'netplan' for networing stuff, whereas earlier Ubuntus use 'ifupdown'.
    Googling shows that all attemtps building a reliable accesspoint on Ubuntu 18.04 with netplan fail (at least that is my impression after a lot of searching...)
    So, people do the following: They deactivate netplan and install again 'ifupdown'. (Then the 'old' method with hoastapd and bridge-utils should work again)

    However, when I do this on this image, I loose all networks on the Joggler - probably, because the image depends on netplan ....
    LMS 8 on Open Peak Joggler (running Chills Jivelite on Joggler)
    Player: 5 x Squeezebox Classic, Slimp3, SqueezeAmp
    2nd System: PiCorePlayer (and LMS) on Pi Zero;

  6. #296
    Senior Member
    Join Date
    Jul 2009
    Posts
    488

    Networking AccessPoint Problem...

    No feedback so far...
    Maybe, I was to wordy?

    -> Can anybody tell me how I can change this image from using the std. Ubuntu 18.04 'netplan' package to the 'older std. method' of Ubuntu using the ifupdown package?

    @chill: Can you give me some hints on how to approach this, or should I rather persue asking in the Joggler Forum about this topic?

    Thank you and I hope all are & stay well!

  7. #297
    Senior Member chill's Avatar
    Join Date
    Mar 2007
    Location
    Nottingham, UK
    Posts
    1,600
    Quote Originally Posted by slimhase View Post
    No feedback so far...
    Maybe, I was to wordy?

    -> Can anybody tell me how I can change this image from using the std. Ubuntu 18.04 'netplan' package to the 'older std. method' of Ubuntu using the ifupdown package?

    @chill: Can you give me some hints on how to approach this, or should I rather persue asking in the Joggler Forum about this topic?

    Thank you and I hope all are & stay well!
    I wish I could help. Netplan is what came with the image that Roobarb provided, so that's what I stuck with. My Linux skills are rudimentary at best, and it was all I could do to get Jivelite and Squeezelite working, with considerable help from Ralphy. Hopefully someone with more experience can chip in here.

  8. #298
    Senior Member chill's Avatar
    Join Date
    Mar 2007
    Location
    Nottingham, UK
    Posts
    1,600
    I guess you've probably seen it already, but it this any good?

  9. #299
    Senior Member
    Join Date
    Jul 2009
    Posts
    488
    Quote Originally Posted by chill View Post
    I guess you've probably seen it already, but it this any good?
    Thanks for your feedback, chill!

    I think, i tried that (and failed), but I give it another go.
    LMS 8 on Open Peak Joggler (running Chills Jivelite on Joggler)
    Player: 5 x Squeezebox Classic, Slimp3, SqueezeAmp
    2nd System: PiCorePlayer (and LMS) on Pi Zero;

  10. #300
    Senior Member
    Join Date
    Jul 2009
    Posts
    488

    Finally - AP works!

    I got it finally to work.... It was quite the puzzle, as I found nothing on the web, which describes it consistently in 1 post.

    So, I posted a how to here:
    https://askubuntu.com/a/1222475/1060413

    The only additional thing to do after following the above generic instructions to work for this image, is this:

    Copy the network.yaml from /etc/netplan/network.yaml also on the root of the FAT partition!

    Me so happy.
    Now, my Joggler has all the functionality as with Roobarbs Image, but with an up to date Ubuntu.

    Thanks again, @chill!
    LMS 8 on Open Peak Joggler (running Chills Jivelite on Joggler)
    Player: 5 x Squeezebox Classic, Slimp3, SqueezeAmp
    2nd System: PiCorePlayer (and LMS) on Pi Zero;

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •