Home of the Squeezebox™ & Transporter® network music players.
Page 143 of 143 FirstFirst ... 4393133141142143
Results 1,421 to 1,430 of 1430
  1. #1421
    Junior Member
    Join Date
    May 2021
    Posts
    19
    Quote Originally Posted by Jeff07971 View Post
    I'm guessing the screen you have won't accept the resolution of the default joggler skin.

    Have you tried plugging into a TV and setting to an acceptable resolution for the other screen ?
    it's a 1080p portable hdmi monitor, I have not tried any other screens

  2. #1422
    Senior Member Jeff07971's Avatar
    Join Date
    Aug 2011
    Location
    London, England
    Posts
    1,647
    Quote Originally Posted by ggotnomoney View Post
    it's a 1080p portable hdmi monitor, I have not tried any other screens
    I would try on a TV, JL starts at (800x480 I think) low resolution if the monitor cannot sync to this it will remain blank (one of my PC monitors does this)

    Then set a 1920x1080 skin and try the monitor again

    EDIT: I think I see the "Jivelite" splash screen though but I cannot remember for definite

    Want a webapp ? Get SqueezeLite-X ! https://forums.slimdevices.com/showt...l=1#post903953

  3. #1423
    Junior Member
    Join Date
    May 2021
    Posts
    19
    Quote Originally Posted by Jeff07971 View Post
    I would try on a TV, JL starts at (800x480 I think) low resolution if the monitor cannot sync to this it will remain blank (one of my PC monitors does this)

    Then set a 1920x1080 skin and try the monitor again

    EDIT: I think I see the "Jivelite" splash screen though but I cannot remember for definite
    I will give this a try and report back, thanks again!

  4. #1424
    Junior Member
    Join Date
    May 2021
    Posts
    19
    Quote Originally Posted by Jeff07971 View Post
    I would try on a TV, JL starts at (800x480 I think) low resolution if the monitor cannot sync to this it will remain blank (one of my PC monitors does this)

    Then set a 1920x1080 skin and try the monitor again

    EDIT: I think I see the "Jivelite" splash screen though but I cannot remember for definite
    so I attached it to a tv and still not working, I also do not see a JL splashscreen at all.

  5. #1425
    Junior Member
    Join Date
    May 2021
    Posts
    19
    so I finally got it working. I did a full update, I was on 6.0 and updated to 7.0 and now it works. Thanks for all the suggestions and help!

  6. #1426
    Senior Member
    Join Date
    Dec 2015
    Posts
    134
    Good Morning to all,

    I have a Problem with VU-Meters.
    They work with flac files but the "needels" did not move with dsd files.
    Is there anybody who can help me.

    Greetings Daniel

  7. #1427
    Junior Member
    Join Date
    May 2008
    Location
    Melbourne, Australia
    Posts
    26

    Issue with 3.5" Waveshare Pi4 PcP 7 and calibration.

    Hi,
    I'm trying to set up a 3.5" Waveshare screen on PcP7, Pi4b.
    Using pcp-jivelite_wav35skin.tcz skin.

    I'm following http://www.pughx2.com/picore3.html.
    I have the screen running, but calibration is somewhat bad. When I run calibrate I don't get all the way through.
    Maybe 2 or 3 crosses in the corners, one in the middle then crashes out.
    When I run the test, the stylus is 1cm or so from the cross-hairs.
    If I boot with jivelite, I can sort of navigate the setup menu using the stylus, however the back button (top lerft) is not selectable (I'm supposing because the calibration is poor?)
    So I can drill down and select a wallpaper, or skin, etc, but can't back out.

    Also the screen is in 'negative'. I.e. with black wallpaper it is white, and the "now playing" image is negative also.

    Help appreciated.

    Note. I'm not interested in the touch feature anyway.
    I just want to use the display and control via a phone/pc etc.
    So if there's a way to change the settings remotely (not via the TS) that would be enough.

    Thaks, Matt
    Melbourne, Australia
    piCore Player 7 on Raspberry pi 4b

  8. #1428
    Quote Originally Posted by mfwalker1 View Post
    Hi,
    I'm trying to set up a 3.5" Waveshare screen on PcP7, Pi4b.
    Using pcp-jivelite_wav35skin.tcz skin.

    I'm following http://www.pughx2.com/picore3.html.
    I have the screen running, but calibration is somewhat bad. When I run calibrate I don't get all the way through.
    Maybe 2 or 3 crosses in the corners, one in the middle then crashes out.
    When I run the test, the stylus is 1cm or so from the cross-hairs.
    If I boot with jivelite, I can sort of navigate the setup menu using the stylus, however the back button (top lerft) is not selectable (I'm supposing because the calibration is poor?)
    So I can drill down and select a wallpaper, or skin, etc, but can't back out.

    Also the screen is in 'negative'. I.e. with black wallpaper it is white, and the "now playing" image is negative also.

    Help appreciated.

    Note. I'm not interested in the touch feature anyway.
    I just want to use the display and control via a phone/pc etc.
    So if there's a way to change the settings remotely (not via the TS) that would be enough.

    Thaks, Matt
    I am far away of the experts, but I have a couple 3,5ö touchscreen running with no problem, I do it following these instructions: https://docs.picoreplayer.org/projects/add-a-display/

    A couple of time before I tried the same tutorial than you with no success.

    Cheers,


    Sent from my iPhone using Tapatalk

  9. #1429
    Junior Member
    Join Date
    May 2008
    Location
    Melbourne, Australia
    Posts
    26
    Quote Originally Posted by tobal2 View Post
    I am far away of the experts, but I have a couple 3,5ö touchscreen running with no problem, I do it following these instructions: https://docs.picoreplayer.org/projects/add-a-display/

    A couple of time before I tried the same tutorial than you with no success.

    Cheers,


    Sent from my iPhone using Tapatalk
    Thanks for the reply tobal2.
    I tried using the procedure in the link you provided without success.

    Now I can't get Jivelite to display on this screen at all...
    Even after re-installing PcP from the same downloaded image as the first install.


    It might be faulty. I will try with another distro at some point.
    Meahnwhile I've ordered a OSOYOO 3.5: HDMI screen to see if I have more success.

    THanks,
    mfwalker1
    Melbourne, Australia
    piCore Player 7 on Raspberry pi 4b

  10. #1430
    Senior Member
    Join Date
    Jul 2010
    Posts
    263
    I've set pCP/jivelite to return to the NowPlaying screen after x seconds without interaction (is it called the screensaver setting?).
    And I've noticed that this 'screensaver setting' doesn't apply to the NowPlaying's current playlist screen - which makes sense.

    Do you think you could add another exception for the lyrics submenu?
    Right now it's really hard to following the lyrics of a track when the screensaver kicks in again and again after x seconds (though I do want the screensaver to do just that anywhere else).
    Thank you.

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •