Announcement

Collapse
No announcement yet.

Pcp and Ir control

Collapse
X
Collapse
 
  • Page of 3
  • Filter
  • Time
  • Show
Clear All
new posts
Previous 1 2 3 template Next
    #31
    Mine does the same at boot although my remote is Sony and does work.



    Code:
    [   16.308079] Registered IR keymap rc-rc6-mce
[   16.325021] IR RC6 protocol handler initialized
[   16.360083] rc rc0: gpio_ir_recv as /devices/platform/[email protected]/rc/rc0
[   16.360575] rc rc0: lirc_dev: driver gpio_ir_recv registered at minor = 0, raw IR receiver, no transmitter
[   16.361064] input: gpio_ir_recv as /devices/platform/[email protected]/rc/rc0/input0

    What is the output from "sudo ir-keytable" ?

    What is the output from "sudo ir-keytable -t" when a key on the remote is pressed ?

    Jeff
    sigpic
    Want a webapp ? Get SqueezeLite-X ! https://forums.slimdevices.com/showt...l=1#post903953

    Comment

      #32
      Originally posted by Jeff07971 View Post
      Mine does the same at boot although my remote is Sony and does work.

      What is the output from "sudo ir-keytable" ?
      [email protected]:~$ sudo ir-keytable
      Found /sys/class/rc/rc0/ (/dev/input/event0) with:
      Name: gpio_ir_recv
      Driver: gpio_ir_recv, table: rc-rc6-mce
      LIRC device: /dev/lirc0
      Supported kernel protocols: lirc rc-5 rc-5-sz jvc sony nec sanyo mce_kbd rc-6 sharp xmp imon
      Enabled kernel protocols: lirc rc-6
      bus: 25, vendor/product: 0001:0001, version: 0x0100
      Repeat delay = 500 ms, repeat period = 125 ms


      Originally posted by Jeff07971 View Post

      What is the output from "sudo ir-keytable -t" when a key on the remote is pressed ?
      oooups nothing. Tsop is on PIN25 and I saw values when LIRC was installed

      Comment

        #33
        Originally posted by PaulH View Post
        [email protected]:~$ sudo ir-keytable
        Found /sys/class/rc/rc0/ (/dev/input/event0) with:
        Name: gpio_ir_recv
        Driver: gpio_ir_recv, table: rc-rc6-mce
        LIRC device: /dev/lirc0
        Supported kernel protocols: lirc rc-5 rc-5-sz jvc sony nec sanyo mce_kbd rc-6 sharp xmp imon
        Enabled kernel protocols: lirc rc-6
        bus: 25, vendor/product: 0001:0001, version: 0x0100
        Repeat delay = 500 ms, repeat period = 125 ms




        oooups nothing. Tsop is on PIN25 and I saw values when LIRC was installed

        Pin 25 is Ground, do you mean Pin 22 GPIO25 ?

        I'm not sure whats going on here its worked fine for me for many years and reinstalls.

        Are you sure theres nothing extra you've done over what you've told us ?

        Jeff
        sigpic
        Want a webapp ? Get SqueezeLite-X ! https://forums.slimdevices.com/showt...l=1#post903953

        Comment

          #34
          Theres something weird going on somewhere !

          I loaded your conf file

          Code:
          #table: Apple, type: nec
0x87eee20b  KEY_UP
0x87eee20d  KEY_DOWN
0x87eee208  KEY_LEFT
0x87eee207  KEY_RIGHT
0x87eee20e  KEY_P
0x87eee202  KEY_0
          and I get

          Code:
          [email protected]:~$ sudo ir-keytable
Found /sys/class/rc/rc0/ (/dev/input/event0) with:
        Name: gpio_ir_recv
        Driver: gpio_ir_recv, table: rc-rc6-mce
        LIRC device: /dev/lirc0
        Supported kernel protocols: lirc rc-5 rc-5-sz jvc sony nec sanyo mce_kbd rc-6 sharp xmp imon
        Enabled kernel protocols: lirc nec
        bus: 25, vendor/product: 0001:0001, version: 0x0100
        Repeat delay = 500 ms, repeat period = 125 ms

          Notice two enabled protocols
          sigpic
          Want a webapp ? Get SqueezeLite-X ! https://forums.slimdevices.com/showt...l=1#post903953

          Comment

            #35
            Originally posted by Jeff07971 View Post
            Pin 25 is Ground, do you mean Pin 22 GPIO25 ?
            Of course!! My mistake !


            Originally posted by Jeff07971 View Post
            Are you sure theres nothing extra you've done over what you've told us ?
            I'm using an HfiBerry DAC2


            Why I don't have this line:
            Enabled kernel protocols: lirc nec

            Does the table has a special name/extension ???
            Last edited by PaulH; 2022-01-20, 14:50.

            Comment

              #36
              When you say

              D/A choice, resize files, LMS, Jivelite install, Kernel keytables install, upload IRfile
              Where do you upload "upload IRfile"

              Click image for larger version Name: 2022-01-19 09_58_23-pCP - LIRC — Mozilla Firefox.jpg Views: 1 Size: 49.5 KB ID: 1574272

              Here ?
              sigpic
              Want a webapp ? Get SqueezeLite-X ! https://forums.slimdevices.com/showt...l=1#post903953

              Comment

                #37
                Originally posted by Jeff07971 View Post
                When you say



                Where do you upload "upload IRfile"

                [ATTACH]36950[/ATTACH]

                Here ?
                Not sure. It's not the same color...
                Click image for larger version Name: Capture d’écran 2022-01-20 à 16.21.36.jpg Views: 1 Size: 200.2 KB ID: 1574273

                Comment

                  #38
                  Here

                  Click image for larger version Name: Capture d%u2019écran 2022-01-20 à 16.21.36.jpg Views: 1 Size: 207.0 KB ID: 1574274

                  Sorry I have "Dark" Theme turned on

                  Jeff
                  sigpic
                  Want a webapp ? Get SqueezeLite-X ! https://forums.slimdevices.com/showt...l=1#post903953

                  Comment

                    #39
                    Exactly at this place !
                    Uploading with this message:
                    Code:
                    [ INFO ] Uploading: jivelite keytables
[ INFO ] Backing up files to /mnt/mmcblk0p2/tce/mydata.tgz / 
Done.
[ OK ] Backup successful.
[ INFO ] Loading keytable
[ INFO ] Backing up files to /mnt/mmcblk0p2/tce/mydata.tgz / 
Done.
[ OK ] Backup successful.
                    and:
                    Code:
                    [email protected]:~$ sudo ir-keytable
Found /sys/class/rc/rc0/ (/dev/input/event0) with:
	Name: gpio_ir_recv
	Driver: gpio_ir_recv, table: rc-rc6-mce
	LIRC device: /dev/lirc0
	Supported kernel protocols: lirc rc-5 rc-5-sz jvc sony nec sanyo mce_kbd rc-6 sharp xmp imon 
	Enabled kernel protocols: lirc rc-6 
	bus: 25, vendor/product: 0001:0001, version: 0x0100
	Repeat delay = 500 ms, repeat period = 125 ms

                    Comment

                      #40
                      OK

                      We now know that its software !

                      Your conf file runs OK on my pCP and enables NEC protocol but dosent on your pCP

                      I called your file "Nec.conf" and edited it in MS Windows Notepad

                      Nec.conf

                      Can you upload this and try "sudo ir-keytable" and "sudo ir-keytable -t" again

                      Jeff
                      sigpic
                      Want a webapp ? Get SqueezeLite-X ! https://forums.slimdevices.com/showt...l=1#post903953

                      Comment

                        #41
                        Originally posted by Jeff07971 View Post
                        OK

                        We now know that its software !

                        Your conf file runs OK on my pCP and enables NEC protocol but dosent on your pCP

                        I called your file "Nec.conf" and edited it in MS Windows Notepad

                        [ATTACH]36954[/ATTACH]

                        Can you upload this and try "sudo ir-keytable" and "sudo ir-keytable -t" again

                        Jeff
                        [ INFO ] Uploading: jivelite keytables
                        [ INFO ] Backing up files to /mnt/mmcblk0p2/tce/mydata.tgz /
                        Done.
                        [ OK ] Backup successful.
                        [ INFO ] Loading keytable
                        [ INFO ] Backing up files to /mnt/mmcblk0p2/tce/mydata.tgz /
                        Done.
                        [ OK ] Backup successful.




                        Wahou !!!

                        Found /sys/class/rc/rc0/ (/dev/input/event0) with:
                        Name: gpio_ir_recv
                        Driver: gpio_ir_recv, table: rc-rc6-mce
                        LIRC device: /dev/lirc0
                        Supported kernel protocols: lirc rc-5 rc-5-sz jvc sony nec sanyo mce_kbd rc-6 sharp xmp imon
                        Enabled kernel protocols: lirc nec
                        bus: 25, vendor/product: 0001:0001, version: 0x0100
                        Repeat delay = 500 ms, repeat period = 125 ms

                        [email protected]:~$ sudo ir-keytable -t
                        Testing events. Please, press CTRL-C to abort.
                        21908.790063: lirc protocol(nec32): scancode = 0x87eee25e
                        21908.790086: event type EV_MSC(0x04): scancode = 0x87eee25e
                        21908.790086: event type EV_SYN(0x00).
                        21908.880094: lirc protocol(nec32): scancode = 0x87eee204
                        21908.880108: event type EV_MSC(0x04): scancode = 0x87eee204
                        21908.880108: event type EV_SYN(0x00).

                        It works!!!!

                        I saw too late my file has a .rtf extension. That probably why it doesn't work but without any error message !!!


                        Thanks a lot Jeff !!!!! GREAT JOB !!!

                        Comment

                          #42
                          Phew !!! Got there in the end !

                          I noticed I had a filename problem once before, its even in the thread "Howto create a linux kernel IR remote keytable for Jivelite on piCorePlayer 5.x/6.x "

                          Oh well !

                          Glad you got it working

                          Enjoy

                          Jeff
                          sigpic
                          Want a webapp ? Get SqueezeLite-X ! https://forums.slimdevices.com/showt...l=1#post903953

                          Comment

                            #43
                            Originally posted by Jeff07971 View Post
                            Phew !!! Got there in the end !

                            I noticed I had a filename problem once before, its even in the thread "Howto create a linux kernel IR remote keytable for Jivelite on piCorePlayer 5.x/6.x "

                            Oh well !

                            Glad you got it working

                            Enjoy

                            Jeff
                            Perfect!!! I sent you a PM.

                            Comment

                              #44
                              Originally posted by PaulH View Post
                              I saw too late my file has a .rtf extension. That probably why it doesn't work but without any error message !!!
                              rtf is rich text, the file must be plain text. We can handle the Dos->Unix line endings, but not much else. There is very little error checking going on with the file you upload......it takes the user knows what to do. I would have to add some more dependencies to do more error checking.

                              Notepad++ is the best windows editor for working on files on a linux system.
                              piCorePlayer a small player for the Raspberry Pi in RAM.
                              Homepage: https://www.picoreplayer.org

                              Please donate if you like the piCorePlayer

                              Comment

                                #45
                                Originally posted by paul- View Post
                                Notepad++ is the best windows editor for working on files on a linux system.
                                I fully agree with you! Unfortunately it didn't exist for MAC. I made the file (RTF!) with Textedit.

                                Normally Mac should be closer to linux than window.... :-(

                                Comment

                                Previous 1 2 3 template Next
                                Working...
                                X

                                We process personal data about users of our site, through the use of cookies and other technologies, to deliver our services, personalize advertising, and to analyze site activity. We may share certain information about our users with our advertising and analytics partners. For additional details, refer to our Privacy Policy.

                                By clicking "I AGREE" below, you agree to our Privacy Policy and our personal data processing and cookie practices as described therein. You also acknowledge that this forum may be hosted outside your country and you consent to the collection, storage, and processing of your data in the country where this forum is hosted.

                                I Agree