Patch for HDD Standby on QNAP X09

[volpone]

Hi Volpone,

i am quite sure that the migration to Synology is possible since i've had one DS106 in the past and my older version (for SSODS 2.XX) worked reliable.

The problem is that i have no DS available and it is not possible for me to adapt the script without any tool to test it(actually i even don't know if it works for QNAP209 and 409) :-(

Mr_Hyde,
Two solutions for Synology migration:

1) I give you telnet or Putty access to my DS207+ to test your scripts.

or

2) You know somebody with a very good Linux experience (as yours) who own a Synology DS and is interested in such migration.

Let me know.

Regards

Volpone

[lucas72]

Mr_Hyde,
Two solutions for Synology migration:

1) I give you telnet or Putty access to my DS207+ to test your scripts.

or

2) You know somebody with a very good Linux experience (as yours) who own a Synology DS and is interested in such migration.

Let me know.

Regards

Volpone

...or


3) Move to QNAP TS209 ! :P

[Hellsblade]

just to let you know i upgraded to the last version 0.3a and i'm using it on a TS209.
Only the smartinfo on 2 disks does'nt seem to work properly.

This shown in the General status report;
SMART Info: │
│ /dev/md0: │
│ │
│ /dev/md0: │
│ │

I'm using the disks in a raid0 config.

rgds,
Hellsblade

[volpone]

just to let you know i upgraded to the last version 0.3a and i'm using it on a TS209.
Only the smartinfo on 2 disks does'nt seem to work properly.

This shown in the General status report;
SMART Info: │
│ /dev/md0: │
│ │
│ /dev/md0: │
│ │

I'm using the disks in a raid0 config.

rgds,
Hellsblade

Hellsblade,
Apart the smart problem, does your TS209 hibernate correctly with usbswap and not without ?

Regards

Volpone

[mr_hyde]

just to let you know i upgraded to the last version 0.3a and i'm using it on a TS209.
Only the smartinfo on 2 disks does'nt seem to work properly.

This shown in the General status report;
SMART Info: │
│ /dev/md0: │
│ │
│ /dev/md0: │
│ │

I'm using the disks in a raid0 config.

rgds,
Hellsblade

Hi Hellsblade,

could you pls. post the result of 'cat /proc/mounts'

And i also would be interested, if the tool goes into standby only with the patch. Then i could add this to the readme.

mr_hyde

[phibes4000]

Per my earlier post, would you expect this to work with RAID1 or does the sync get in the way?

[mr_hyde]

Per my earlier post, would you expect this to work with RAID1 or does the sync get in the way?

Sorry, but i have no experience with RAID since i've got only the one disk drive. Bu tprobably ist could also work, since the activities are directed to USb which should not be involved by RAID.

[Hellsblade]

As requested the cat output. About standby mode, unfortunately my NAS is constantly in use by the rest of the family with al kinds of BT tasks. I'm sure they will evict me when i kill there tasks in t queue ;-). But when i first installed the utility the stop start counter did go up once. It has not done that for a couple of months. I think we'll have to move this question to the QNAP forum to find someone who can confirm your standby question.

[~] # cat /proc/mounts
rootfs / rootfs rw 0 0
/dev/root / ext2 rw 0 0
/proc /proc proc rw,nodiratime 0 0
none /dev/pts devpts rw 0 0
sysfs /sys sysfs rw 0 0
tmpfs /tmp tmpfs rw 0 0
usbfs /proc/bus/usb usbfs rw 0 0
/dev/sda4 /mnt/ext ext2 rw 0 0
/dev/md9 /mnt/HDA_ROOT ext3 rw 0 0
/dev/md0 /share/MD0_DATA ext3 rw 0 0
/dev/sdo1 /share/external/sdo ext3 ro 0 0
/dev/sdu1 /share/external/sdu ext3 rw 0 0
/dev/root /mnt/HDA_ROOT/rootfs_2_3_6/bin ext2 rw 0 0
/dev/root /mnt/HDA_ROOT/rootfs_2_3_6/dev ext2 rw 0 0
/dev/md9 /mnt/HDA_ROOT/rootfs_2_3_6/etc/config ext3 rw 0 0
/proc /mnt/HDA_ROOT/rootfs_2_3_6/proc proc rw,nodiratime 0 0
/dev/md0 /mnt/HDA_ROOT/rootfs_2_3_6/share/Qdownload ext3 rw 0 0
tmpfs /mnt/HDA_ROOT/rootfs_2_3_6/tmp tmpfs rw 0 0
tmpfs /.eaccelerator.tmp tmpfs rw 0 0
[~] #

FYI I have 1 1GB USB stick 1 500GB(ext3)USB disk and 2 internal 500GB Samsung disks in raid0.

Rgds,
hellsblade.

[mlavende]

Mr Hyde

Hmmmm. I'm not sure if I can use this. I bought a TS-109Pro with Slimserver already installed from qnap.co.uk. Like so many others it doesn't sleep properly. I saw this post from you and thought I could use your script with a 1GB stick.
However when I run usbutil.sh I get the message

Not found PS of SSODS. Please install SSOTS first!

I've never even heard of SSOTS or SSODS but I gather from a quick look around that it's another way of installing slimserver on a TS-109. I assume this has a totally different directory structure...

Am I on the right track or can someone make this script work for me please?

-Mat

p.s. I don't suppose you're the same hyde from the Toppy forums?

[mr_hyde]

Mr Hyde

Hmmmm. I'm not sure if I can use this. I bought a TS-109Pro with Slimserver already installed from qnap.co.uk. Like so many others it doesn't sleep properly. I saw this post from you and thought I could use your script with a 1GB stick.
However when I run usbutil.sh I get the message

Not found PS of SSODS. Please install SSOTS first!

I've never even heard of SSOTS or SSODS but I gather from a quick look around that it's another way of installing slimserver on a TS-109. I assume this has a totally different directory structure...

Am I on the right track or can someone make this script work for me please?

-Mat

p.s. I don't suppose you're the same hyde from the Toppy forums?

For the progressive installation look her:
http://forums.slimdevices.com/showth...hlight=standby

If you wnat to use Squeezecenter 7.0+ on your QNAP than you have to remove progressive and install SSODS (SSOTS). Therefore you can use the patch of this thread which works reliable for me (also the other was working for progressive installation)

BTW, i prefer SC7.0 since a couple of improvements are included.